Jonsered 1188S CE Скачать руководство пользователя

Страница: 42 / 96

6. HPC [option]

Hydraulic Pilot Control (HPC) is an optional control system that gives you smooth and easy
operation.

• Precision control over your crane movements
• Smooth, flawless operation.
• Reduced stress on crane structure
• Increased life expectancy of your equipment

With 2 or 4 joysticks.

Adjust the joysticks, High seat

Release the lower wheel by turning it counter
clockwise.

Adjust the height of the joystick.

Lock the lower wheel by turning it clockwise.

Release the upper wheel by turning it counter
clockwise.

Adjust the angle of the joystick.

Lock the upper wheel by turning it clockwise.

Adjust the joysticks, Cabin

Release the lower handle.

Adjust the height of the joystick.

Lock the lower handle.

Release the upper lever.

Adjust the angle of the joystick.

Lock the upper lever.

HPC [option]

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды