Jonsered 1188S CE Скачать руководство пользователя

Страница: 36 / 96

3. Park the crane straight backward with a piece of wood underneath the crane tip to prevent

damage.

4. Disconnect the power take off to ensure that the hydraulic system is without pressure.
5. Disconnect the crane from the chassis.
6. Slowly drive the vehicle away from the crane.

WARNING

Take care when mounting/dismounting the crane on/off the vehicle.

Roughly handling can seriously damage the crane or the vehicle.

Driving with the crane

DANGER

• Never drive the vehicle if there is a load

suspended from the crane.

• Before you move the vehicle:

Check that there is no pump flow to the
main control valve. The PTO or power
supply must be disengaged. The operating
system must be switched off!

• Pay attention to the width and height of the

crane in the transport position. The crane
has to stay within the width of the truck.
Make sure the parked crane can not hit
bridges, tunnels etc.

• Pay attention to overhead power lines!

Make sure that no part of the crane ever
comes in contact with overhead power
lines.

For further instructions see vehicle's manual(s).

Safety precautions and warnings

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды