Jonsered 1188S CE Скачать руководство пользователя

Страница: 48 / 96

Weight - Calibration

This menu is used to calibrate the weight. If there is a
missmatch comparing with the scale on the vehicle

use arrows to adjust the weight. Confirm and save

with the button

Change language

Use this menu to change the language used in the

display. Select the wanted language with the arrows

and confirm with the button

. A restart is needed

before any changes can be seen.

Copy driver settings

Copy settings from another driver. Select a driver to

copy from with the arrows and confirm with the

button

LEDs for indication of the system’s operational status

All units in the TimberTronics system are equipped with two LEDs (1) to indicate operational status;

཰

The control system TimberTronics [option]

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды