Jonsered 1188S CE Скачать руководство пользователя | Manualshive

Страница: 51 / 96

background image

8. The control system Multidrive2 [option]

8.1. The control system Multidrive2

The MultiDrive2 control system is a control system used in Jonsered and Loglift cabin cranes. With
the MultiDrive system you can:

• Monitor the crane operating data
• Save different user profiles

8.2. Components in the Multidrive2 System

Components in the MultiDrive2 system

Control levers (placed inside the cabin )

PDF box (placed on the crane)

Display (placed inside the cabin)

DA modules (placed on the main control valve and on the
stabiliser control valve)

8.3. Multidrive2 control levers and display

Press the standby button on the cabins control panel to start the system. The Multidrive2 control
system consists of two control levers, each control lever consists of five buttons.

NOTE

The buttons “SPEED” and “CHANGE” are lever specific. The buttons on the right
lever controls the settings for the right lever and the buttons on the left lever
controls the settings for the left lever.

Olsb

ergs

Olsb

ergs

The control system Multidrive2 [option]

Jonsered 1188S CE

51

«
...
49
50
51
52
53
...
»

Содержание 1188S CE

































































































Отзывы:

Нет отзывов

Похожие инструкции для 1188S CE

MicroVersaTrip Plus

Бренд: GE Страницы: 20

MicroVersaTrip Plus

Бренд: GE Страницы: 2

Бренд: GE Страницы: 252

Бренд: Balanced Body Страницы: 12

Бренд: Eagle Pro Страницы: 6

Бренд: GE Страницы: 10

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: ZIGBEE Страницы: 6

Бренд: Daisy Страницы: 2

Below Ground Pool Cover Box

Бренд: Daisy Страницы: 3

Бренд: DB Industries Страницы: 60

Бренд: vc999 Страницы: 55

Бренд: Salsbury Industries Страницы: 4

Бренд: Garmin Страницы: 2

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренд: Yamaha Страницы: 39

Бренд: Yamaha Страницы: 110

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды