Jonsered 1188S CE Скачать руководство пользователя

Страница: 16 / 96

2.8. Cabin [option]

(1) Front door

(2) Protective curtain

(3) Work lights

(4) Side door

(5) Warning light

(6) Service hatch

(7) Heater/cooler

(8) Control panel

2.8.1. Control panel in the cabin C912

NOTE

The top on the control panel depends on the selected heating/cooling system. For
diesel heather, see section diesel heather.

(1) Electric Control (Stand by)

(2) PTO

(3) Stabiliser extension in/out

(4) Left stabiliser leg in/out

(5) Extra button

(6) Cabin up/down

(7) Work light, crane boom

(8) Work light, roof

(9) Windshield washer

(10) Wiper

(11) Extra button

(12) Blind plug

(13) Switch for diesel heater [option]

(14) Right stabiliser leg in/out

(15) Stop button

(16) Extra button

(17) Over load warning

(18) Warning light

(19) Button to be used when operating the stabiliser system

(20) 12V outlet

(21) Seat heater

཰

ཱ

ི

ུ

ཱི

ཱུ

ྲྀ

ཷ

Structure and parts of the crane

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды