Jonsered 1188S CE Скачать руководство пользователя

Страница: 15 / 96

2.6. Buttons on the control panel [option]

Control the stabiliser system from the high seat [option]

The crane and the stabiliser system can be operated from
the high seat.

(1) Stabiliser leg, left

(2) Stabiliser leg, right

(3) Stabiliser extension out/in

(4) Console or optional function

(5) Bunk movement

(6) Lights

(7) Load weighing device [option] / activation of the main
control [HPC option]

(8) Seat heat [option]

(9) Button to be used together with (1), (2), (3)

(10) Optional button

DANGER

Take care not to put your foot on the pedals when taking place in the high seat.
Unintentional crane movements can occur.

Before leaving the high seat, switch off the system from the control panel,
deactivate the main control (HPC).

2.7. Premium high seat [option]

(1) Handle to adjust seat forward/backward

(2) Seat belt

(3) Handle to adjust height of the seat

(4) Locking device for seat tilting

(5) Handle to adjust armrest

DANGER

For cranes with joysticks and HPC, always deactivate HPC before leaving the high
seat.

DANGER

Take care not to put your foot on the pedals when taking place in the high seat.
Unintentional crane movements can occur.

Structure and parts of the crane

Jonsered 1188S CE

Содержание 1188S CE

































































































Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды

Jonsered 1188S CE, Руководство оператора

Результаты поиска

Содержание 1188S CE

Отзывы:

Похожие инструкции для 1188S CE

Бренды по названию

Популярные бренды