Isokern Magnum 86072-60 Скачать руководство пользователя страница 6

Страница: 6 / 56

Safety Instructions

Before starting the Magnum 86072 Series fireplace and

DM chimney installation, read these installation instructions

carefully to be sure you understand them completely. Failure

to follow them could cause fireplace malfunction resulting in

serious injury or property damage.

Always check local building codes governing fireplaces and

fireplace installations. The Magnum 86072 Series fireplace and

DM chimney installation must comply with all local, regional,

state and national codes and regulations.

Magnum 86072 Series fireplace and DM chimney systems

are intended for use in any application where a traditional

masonry type fireplace would apply. The chimney system must

always vent vertically to the outside of the building.

Creosote and soot formation and the need for removal: When

wood is burned slowly, it produces tar and other organic vapors

which combine with expelled moisture to form creosote. The

creosote vapors condense in the relatively cool chimney flue of

a slow burning fire. As a result, creosote residue accumulates

on the flue lining. When ignited this creosote makes an

extremely hot fire.

Because of creosote and soot buildup it is necessary

to inspect and clean the fireplace and chimney prior to use

and periodically during the heating season. Cleaning of the

fireplace and the chimney system should be done annually at

a minimum. In colder climates, chimney cleaning may need to

be done periodically throughout the heating season.

Before servicing, allow the fireplace to cool. Always shut

off any electricity or gas to the fireplace while working on it.

Use only solid fuel or natural or LP gas log sets in this

unit. Do not use artificial wax based logs, chemical chimney

cleaners or flame colorants in this fireplace.

Never use gasoline, kerosene, gasoline-type lantern fuel,

charcoal lighter fluid, or similar liquids to start or “freshen up”

a fire in this fireplace. Keep all flammable liquids at a safe

distance from the fireplace.

Always keep the flue damper open when heat is present in

the fireplace.

Do not use a fireplace insert or any other product not

specified for use with the Magnum 86072 Series fireplace and

DM chimney systems unless written authorization is given by

Earthcore. Failure to heed this warning may cause a fire hazard

and will void the warranty.

10.

This fireplace is not intended to heat an entire home or

to be used as a primary heat source. It is designed to ensure

homeowner comfort by providing supplemental heat to the

room.

11.

Always ensure that an adequate supply of replacement

combustion air from the outside of the house is accessible to

the fire to support normal combustion. Fireplaces consume

large volumes of air during the normal firing process.

In the event the home is tightly sealed and has modern

energy efficient features, the optional combustion air supply

kits may not provide all the air required to support combustion

and the proper flow of combustion gases up the chimney.

The manufacturer is not responsible for any smoking

or related problems that may result from the lack of adequate

air supply flowing into the house. It is the responsibility of the

builder/contractor to ensure that adequate air supply has been

provided for the fireplace.

12.

“Smoke free” operation is not warranted nor is the

manufacturer responsible for inadequate system draft caused

by mechanical systems, general construction conditions,

inadequate chimney heights, adverse wind conditions or

any unusual environmental conditions or factors beyond the

manufacturer’s control.

Caution:

When used with the Magnum 86072 Series fireplace

system, all gas log sets must be operated with the damper

clamped in the fully open position. This includes unlisted

“vent free” log sets. Only listed “vent free” log sets may be

operated with the damper in the closed position.

13.

When in doubt about a component’s usability - has visible

or suspected physical damage - consult your Isokern distributor

or authorized Isokern representative for advice.

14.

Modification to Magnum 86072components not mentioned

in this manual may void claims, listings and approvals and

could result in an unsafe and potentially dangerous installation.

Alterations to the Magnum 86072 firebox are allowed

with prior written approval and instructions from Earthcore

Industries, LLC. The installer indemnifies the manufacturer of

all claims and under no circumstances will manufacturer be

liable for consequential, incidental, indirect, punitive or other

damages of any kind or nature, whether foreseeable or not,

based on any claim by any party as to the modifications of the

Isokern fireplaces.

15.

Keep all insulation, vapor barriers, “house wrap”

paper and other insulating type membranes and products,

including fiberglass, cellulose and other insulation,

(anything that carries an “R” rating) a minimum of three

inches (3”) away from all firebox and chimney surfaces.

Exception:

If insulation is used in walls surrounding the fireplace,

insulation may be installed behind sheathing of gypsom board,

plywood, particle board or other material on the side facing

the Isokern. The facing material cannot be within 1 1/2” to the

fireplace sidewalls.

WARNING:

Do not pack required air spaces with insulation

or other materials.

16.

Never leave children unattended when there is a fire

burning in the fireplace.

17.

Burning some fuels (such as charcoal) can be hazardous due

to the possibility of producing carbon monoxide, a colorless,

odorless gas. Early signs of carbon monoxide poisoning

resemble flu symptoms, including headaches, dizziness or

nausea. Over exposure to carbon monoxide can lead to illness

and death. It is strongly recommended to install smoke and

carbon monoxide alarm / detector devices wherever fireplaces

are in use.

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды