Isokern Magnum 86072-60 Скачать руководство пользователя страница 47

Страница: 47 / 56

DM Chimney System: Crown Caps

DM Small Crown Cap (Figure 97)

The DM small crown cap is a prefabricated cement

weather cap that measures 26- 1/2” square and 3” thick. The

small crown cap is designed and installed the same as the large

crown cap.

The small crown cap is intended for use where DM

chimneys are to receive thin veneers and cultured stone that do

not require the installation of the Isokern brickledge. The small

crown cap is also suitable where DM chimneys are to receive a

stucco finish.

Other chimney terminations are possible with DM

chimneys. Check local codes for use of custom chimney

terminations and decorative shrouds.

DM Large Crown Cap (Figure 98)

The DM large crown cap is a prefabricated cement

weather cap for masonry veneer chimneys. The large crown cap

measures 37-1/2” square and is 3” thick at its center.

The component has an octagonal hole at its center

so that the top inner liner of the DM chimney stack can pass

through it. The crown cap then sits on the top most DM outer

casing block.

To set the large crown cap the last inner liner should be

at least 3” above the last outer casing block in the chimney stack.

Mortar the top of the last outer casing block. Set the

large crown cap over the inner liner and onto the top of the last

outer casing in the stack.

Caulk or mortar the joint between the octagonal liner

and the crown cap where the liner comes through the top surface

of the large crown cap.

FIGURE 97

FIGURE 98

SMALL

CROWN CAP

LARGE

CROWN CAP

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды