Isokern Magnum 86072-60 Скачать руководство пользователя страница 54

Страница: 54 / 56

Registration Card

Please tear out along dashed lines and send to:

Earthcore Industries

Attn: Technical Dept.

6899 Phillips Industrial Blvd.

Jacksonville, FL. 32256

Or register your Isokern online at: www.earthcore.co

WARRANTY CARD

Purchased From:

Date of Purchase:

_______________________________________________________

Name: _______________________________________________________

Address:

_______________________________________________________

City, State & Zip:

_______________________________________________________

Phone No:

_______________________________________________________

Gas Log Burner Size: (Circle One)

24”

30” Other__________

Fireplace Series/Size: Magnum _____ Isokern Standard _____ IBV ______ Vent-Free _____

Green Tech _____ ISO’ven _______ Fire-Lite Stand? (Circle One) Yes No

Gas Control Valve Type: (Circle One) Remote Control

Safety Pilot

Gas Type: (Circle One)

Natural Gas

Propane

Buyer:

Date of Installation: (Completed) ________________________________________________

Name: _______________________________________________________

Address:

_______________________________________________________

City, State & Zip:

_______________________________________________________

Phone No:

_______________________________________________________

Fireplace Serial Number:

(Located on Rating Plate Inside Fireplace) ___________________

Installed By:

_______________________________________________________

Address:

_______________________________________________________

Phone Number

_______________________________________________________

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды