Isokern Magnum 86072-60 Скачать руководство пользователя страница 12

Страница: 12 / 56

Assembly Instructions - Access Modification

Through-Wall Accesses:

1. Combustion Air Inlet: Combustion air inlet kits though not required

by Earthcore with other ventilating appliances installed.

Check local codes for combustion air inlet requirements.

The following is a general representation of a generic

combustion air kit and not a requirement of Earthcore Industries,

LLC. Local building codes prevail and should be checked before

installation.

Generic fireplace combustion air kits typically consist of a

sliding stainless steel access door affixed to a three inch (3”) or four

inch (4”) diameter stainless steel sleeve approximately twelve inches

(12”) long. An exterior vent with dress plate, weather hood and rodent

prevention screen of a maximum one-quarter inch (1/4”) wire mesh

completes the kit. (Figure 5)

The access door is fitted into the finished fire brick lining at the

interior sidewall of the Magnum 86072 firebox. The twelve inch (12”)

long sleeve can be introduced into the firebox side wall by core drilling

an appropriately sized hole at the selected firebox location. Keep the

top of the access hole no more than six inches (6”) above the finished

firebrick floor. The hole size should allow for a one-quarter inch (1/4”)

mortar joint around the air access sleeve for heat expansion.

The sleeve passes through the firebox wall and must be

connected to metal pipe (by other) - either flexible or rigid - that leads

to the source for outside combustion air, as directly as possible from the

Magnum 86072 Series fireplace (Few to no bends) with a maximum

length of sixty feet (60’).

WARNING:

Do not use combustible duct material. Avoid installing

a combustion air inlet where the opening could be blocked by snow,

bushes or other obstacles. Air inlet must terminate a minimum of three

feet below the chimney cap level. Air inlet ducts shall not terminate in

attic spaces.

2. Gas Line Feed: For a fireplace having the provision for installation of

a gas pipe, the provision is intended only for connection to a decorative

gas appliance.

CAUTION:

When using the decorative appliance, the fireplace damper

must be set in the fully open position. Gas line for gas log sets used in

the Isokern firebox can be routed through the side wall, by drilling an

appropriately sized hole using a masonry drill bit (Figure 7).

3. Electrical Line Feed can be routed through the Magnum 86072 firebox

side walls by drilling an appropriately sized hole using a masonry drill

bit (Figure 6). Be sure to follow the gas log Appliance Manufacturer’s

explicit electrical line connection instructions for vented masonry

fireplace installations.

Gas line and electric line must be fed through separate access holes.

CAUTION:

All access holes must be grouted with mortar – after line

or conduit feed - to seal any gaps or cracks around line feed conduits

(Figure 7).

FIGURE 5

AROUND CONDUIT WITH

NOTE: FILL ANY GAPS

MORTAR.

NON-COMBUSTIBLE).

TYPICAL PLACEMENT OF

(SEE DETAIL BELOW).

SUPPLY AIR VENTILATION
(IF REQUIRED BY CODE).

GAS OR ELECTRIC CONDUIT

FIRE BRICK SIDE

CONDUIT

GAS OR ELECTRIC

EXTERIOR

EXTERIOR AIR VENT
WITH DRESS PLATE.

WALL

FLEX DUCT TO FIREPLACE
FIREBOX, (ALL PARTS

FIGURE 6

FIGURE 7

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды