Isokern Magnum 86072-60 Скачать руководство пользователя страница 5

Страница: 5 / 56

Intended Use Statement

WARNING:

This fireplace has not been tested for use with

doors. To reduce the risk of fire or injury, do not install doors.

Operable doors are acceptable and if doors are required by the

local authority having jurisdiction, then doors must be kept

in the fully open position when the fireplace is in operation.

Isokern does not limit the use of fireplace screens.

Note

: Do not scale drawings. Illustrations in this manual are not

to scale and are intended to show “typical” installations.

Nominal dimensions are given for design and framing

reference only, since actual installations may vary due to

job specific design preferences. Always maintain the stated

minimum clearances to combustible materials. Do not violate

any specific installation requirements.

The Magnum 86072 Series fireplace and DM chimney

system is tested and listed by Warnock Hersey (Intertek Testing

Service) - Report No.

3082504-T1

- to UL 127, and UL

103HT.

Magnum 86072 Series fireplace systems are also

designed for installation in accordance with the National Fire

Protection Association Standard for chimneys, fireplaces, vents

and Solid Fuel-Burning Appliances (NFPA 211).

Intended Product Use Statement:

The Magnum 86072 Series fireplace and DM chimney

systems are intended to burn solid wood fuel, propane or natural

gas.

Note:

Installation of a gas pipe must comply with the Standard for

Decorative Gas Appliances for Installation in Vented Fireplaces,

ANSI Z21.60.

This fireplace is not designed to sit directly on a

combustible floor system. The Fire-Lite application of the

Magnum 86072 Series fireplace is an engineered system and

designed to be built upon a combustible floor system. The Fire-

Lite will also require a design that will support the total weight

of the Isokern fireplace and chimney system. The FTF-13 or

equivalent chimney system

only

must be used with the Fire-

Lite application. Contact the Technical Department at 800-642-

2920 for details.

This fireplace is intended for use as a supplemental

heat source only and is not intended for heavy use as a primary

heating system.

Overfiring, abusive burning or mistreatment will void

any claims (eg. burning construction debris or other highly

flammable material; tossing, kicking or otherwise forcing logs

into the firebox).

Magnum 86072 Series fireplaces and DM chimney

systems are conventional indoor or outdoor fireplaces designed

to appear like traditional masonry fireplaces. Magnum 86072

Series fireplace and DM chimney system units are intended

for installation in residential homes and other buildings of

conventional construction.

Note:

The local authority having code jurisdiction should be

consulted before installation to determine the need to obtain a

permit.

Important areas of concern with the installation of these

fireplaces are: construction of proper load bearing foundation

and concrete support slab; code required hearth extension

substrates and supports; proper assembly of components;

clearance to combustible materials; height of chimney; and,

techniques employed in applying finishing materials to the

fireplace opening and hearth extension.

Each of these important topics will be covered in detail

throughout this manual. Installation personnel must give special

attention to each topic as the installation progresses.

All work performed on, near and adjoining the fireplace

and chimney installation must meet or exceed the specifications

and requirements in this manual and the prevailing local

building code.

Subsequent renovations, additions of cabinets and

storage spaces in the enclosure surrounding the fireplace are

also limited to the specifications in this manual and to the

prevailing local building code.

Isokern is not responsible for other construction work

around the fireplace unit.

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды