Isokern Magnum 86072-60 Скачать руководство пользователя страница 30

Страница: 30 / 56

Ensure There Are No Gaps

Between Firebox and Facing Material

Avoid False Chimneys

Flush Wall Brick Finish Detail

Important:

Since there is no fire brick set along the top of the Magnum’s firebox opening, when setting the noncombustible finished

facing material (code required and supplied by others) across the top of the firebox opening there may be a gap between the back

of the noncombustible finish material and the rough front face of the Magnum 86072 damper beam. Be sure to check for and fill

any gaps with noncombustible Earthcore Mortar in conjunction with placement of the code required noncombustible finish facing

material set across the top of the firebox opening. (Figure 69)

WARNING

Avoid false chimneys.

Important:

Failure to seal any gaps between the front face of the Magnum 86072 damper plate and the back of the noncombustible

finished facing material will create what is known as a “false chimney”. A “false chimney”, in this case, is the narrow gap (mentioned

above) between the back of the noncombustible facing material at the top of the firebox opening and the rough front of the Magnum

86072 damper beam. If left unfilled this gap creates a “false chimney” which can draw smoke, heat and fire out of the firebox into

the space behind the noncombustible finish facing and on up into overhead framed spaces causing a fire hazard.

FIGURE 69

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды