Isokern Magnum 86072-60 Скачать руководство пользователя страница 35

Страница: 35 / 56

DM Chimney System: General Information

The DM chimney is a dual module, refractory masonry

chimney system. It is composed of two precast, mating

components, the outer casing block and an inner liner.

General Information:

This chimney system is designed for installation in

accordance with the National Fire Protection Standard for

Chimneys and Solid Fuel-Burning Appliances, NFPA 211 and

in accordance with codes such as ICC, BOCA Basic/National

Codes, the standard Mechanical Code and the Uniform Building

Codes.

Note:

Illustrations shown reflect “typical” installations with

nominal dimensions and are for design and framing reference

only. Always maintain minimum required clearances to

combustible materials and do not violate any specific installation

requirements.

Required DM Chimney Clearance:

The DM chimney system, rated UL 103HT, is listed

for zero clearance to normal construction materials. The DM

chimney system may be enclosed in a wood chimney chase at

zero clearance to wood framing members.

Note:

A firestop is required wherever a chimney passes between

one zone of a building to another. Ex: When the chimney passes

through the ceiling into the attic area, there must be a sealed area

around the chimney so there isn’t a chaseway for a fire to get to

the attic.

Since lateral support is required for DM chimneys

the framing members will be in contact with the DM chimney

system.

Important:

“Combustibles” are defined as “normal construction

materials” and are considered to be: framing materials, particle

board, mill board, drywall, plywood paneling, plywood sub

flooring, and wood flooring.

Keep all insulation, vapor barriers, “house wrap” paper and

other insulating type membranes and products, including

fiberglass, cellulose and other insulation, (anything that

carries an “R” rating) a minimum of three inches (3”) away

from all firebox and chimney surfaces.

Exception:

If insulation is used in walls surrounding the fireplace,

insulation may be installed behind sheathing of gypsom board,

plywood, particle board or other material on the side facing

the Isokern. The facing material cannot be within 1 1/2” to the

fireplace sidewalls.

Mechanical Vent Systems:

It is acceptable to use mechanical draft systems, if the venting

companies do the engineering calculations and make the

necessary recommendations for fan size and flue vent diameter

following the guidelines of NFPA 211/2006, pg. 211-13.

Installation of such systems must also follow the mechanical

drafting company’s explicit installation and operation

instructions.

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды