Isokern Magnum 86072-60 Скачать руководство пользователя страница 49

Страница: 49 / 56

STEEL ANGLE

FRONT DAMPER

BEAM

SMOKE DOME

COMPONENTS

FRONT

REAR

SIDE”

SLOPING

SIDE”

SLOPING

Structural Information

The Magnum 86072 firebox/smoke dome assembly

has a load capacity that allows for the fireplace system to carry

a limited amount of straight, vertical DM chimney sections.

The load capacity for the 86072, stated as maximum DM

chimney heights without additional structural support is as

follows:

Magnum 86072: Max. 22 feet of DM Chimney Flue

This chimney height is for straight chimneys (no

offsets) and are exclusive of brickledge.

Important:

DM chimneys taller than the above listed maximum

height require a steel angle (minimum of 4” x 4” x 3/8”) be set

across the Magnum 86072 firebox opening when assembling

the unit as a structural lintel.

This steel lintel shall span the Magnum 86072 firebox

opening, bearing fully on the front 4 inches of the firebox side

wall components. The vertical leg of the angle steel lintel should

turn up and sit in front of the Magnum 86072 damper beam

component. (Figure 102)

Important:

For DM chimneys with both offsets and a

brickledge it is important to fully support the last offset block

where the chimney returns to vertical. This is required in order

to provide complete vertical support for the brickledge and its

related loads.

Important:

When placing steel angles or any other steel support

members into the Magnum 86072 fireplace structure maintain a

2” minimum air space around steel members for clearance to

combustible members and combustible surfaces.

FIGURE 102

FIGURE 103

FIGURE 104

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды