Isokern Magnum 86072-60 Скачать руководство пользователя страница 37

Страница: 37 / 56

DM Chimney: Component Weights

Isokern DM Chimney Weights:

Total installed Isokern DM chimney weight will vary

according to each specific installation. Total installed chimney

weight will be based on the overall height and the configuration of

the chimney system.

Chimneys may be straight vertical stacks of DM outer

casing and inner liner (22’-0” Maximum without additional

structural support) but may also include the use of offset chimney

blocks, brickledge, chimney reinforcement, brick/stone veneers,

cement crown caps and clay chimney pot termination.

The DM chimney component weights are as follows:

Small crown cap: 80 lb.

Large crown cap: 100 lb.

Brickledge: 110 lb.

14” diameter inner liner: 45 lb.

Outer casing block: 90 lb.

Offset block*: 110 lb.

*Construction of an offset block sequence will shift a portion, if

not all of the chimney load off of the firebox and smoke dome.

Additional reinforced concrete footing and slab area may need to be

provided adjacent to or as a continuation of the primary support slab

area for bearing the steel or masonry support required for an offset

sequence. (See pages 40-42 following.)

Notes:

Plan chimney configuration carefully before constructing

the required reinforced concrete support foundation for the Magnum

86072 Series fireplace. Be sure that enough structural masonry area

is available to support any offset chimney sequence included in the

proposed chimney design.

Isokern is not responsible for site specific structural support

details and load specifications for Magnum 86072 Series fireplace

and DM chimney system installations. Consult local structural

engineer for proper job-specific support structure design, sizing and

load bearing specifications.

Unless otherwise noted, all floor drawings in this manual

are merely illustrations to indicate the presence of an underlying

noncombustible support structure to the Magnum 86072 installation.

LARGE

CROWN CAP

SMALL

CROWN CAP

BRICKLEDGE

INNER

LINER

OUTER

CASING

OFFSET

BLOCK

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды