Isokern Magnum 86072-60 Скачать руководство пользователя страница 33

Страница: 33 / 56

”

12"

33"

12”

COMBUSTIBLE

MANTLE SHELF

33” HEARTH

EXTENSION

COMBUSTIBLE

FLOOR SYSTEM

ADJOINING

ROOM WALL

HEARTH

EXTENSION

9”

3”

48”

Non-combustible Finished Facing requirements &

Clearance to Combustible Trim

Hearth Extensions:

All Magnum 86072 Series fireplaces shall have hearth

extensions of brick, concrete, stone, tile or other code approved

noncombustible material. Suitable hearth extension material for

the Magnum 86072 Series fireplace shall be placed on the hearth

extension’s noncombustible substrate and must extend to at

least thirty three inches (33”) in front of the fireplace’s finished

opening and must extend to at least twelve inches (12”) beyond

the sides of the finished fireplace opening. (Figure 74 & 75)

WARNING:

The noncombustible hearth extension, by code,

must sit on noncombustible substrate which shall have no wood

underpinnings.

This means that off-grade wood floor systems shall be

constructed in such a way that all wood floor joists and

subflooring shall stop thirty three inches (33”) out from the front

of the Magnum 86072 firebox. (Figure 75)

Mantle and Mantle Shelf Clearances:

Magnum 86072 Series

fireplaces are subject to the same building code safety clearances

to combustible trim as with any radiant heat fireplace.

All combustible trim shall be kept at least nine inches

(9”) from the finished fireplace opening. Combustible trim

located along the sides of the fireplace opening, which project

more than one and one-half inches (1-1/2”) from the face of the

fireplace, shall have additional clearance from the nine inches

(9”) equal to the projection. Combustible projecting mantles

up to twelve inches (12”) of projection - shall not be placed

less than thirty eight inches (38”) from the top of the fireplace

opening. Combustible mantles which project more than twelve

inches (12”) from the face of the fireplace, shall have additional

clearance from the thirty eight inches (38”) equal to the

projection.

Note:

The local authority having jurisdiction may require

greater clearances for projection combustible mantle shelves. Be

sure to check local building codes regarding required clearances

to projecting combustible mantles.

Adjoining Walls.

Side walls and walls to rooms adjoining the

Magnum 86072 Series fireplace installations cannot be closer

than forty eight inches (48”) to the finished fireplace opening.

(Figure 75)

Note:

“Clearance to Combustible Trim” are those distances

required to ensure that a fireplace mantle or facing will not

catch fire. In most cases the distances should also be adequate

to prevent any discoloration or warping due to heat. However

each installation presents a unique and completely different set

of circumstances involving many variables.

These include paint or finish composition, previous

exposure to heat, methods and quality of construction, air flow

patterns, etc. Because of these variables, the manufacturer does

not guarantee that heat warping or discoloration will never

occur.

FIGURE 74

FIGURE 75

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды