Isokern Magnum 86072-60 Скачать руководство пользователя страница 1

Страница: 1 / 56

Isokern ® Magnum ® Fireplace

and DM Chimney System

Installation, Operation and Owner’s Manual

Magnum Model 86072, 60 & 72

A Product of Earthcore

THIS FIREPLACE IS DESIGNED FOR USE WITH

SOLID WOOD LOGS, PLUMBED PROPANE (LP) OR

NATURAL GAS (NG), ONLY

SBCCI

NO.

9626

NYC-MEA

241-90-E

ICC Report NO. ESR-2316

LA RR NO. 25483

IBC 2006, IRC 2006, IMC 2006

Issued: September, 2012

Revision:

INTERTEK TESTING SERVICES REPORT NO. 3082504-T1

2007

Earthcore

Industries,

L.L.C.

THIS MANUAL CAN ONLY BE REPRODUCED IN ITS ENTIRETY

Important:

This manual contains assembly rules, installation steps, guidelines, use and maintenance

instructions for the Magnum 86072 Series fireplace and the DM chimney system. This manual must become

the property of and be reviewed by all current and future users of this product. It is the responsibility of

the general contractor and the installer of this product to ensure that the instructions in this manual are

followed exactly and, further that any allowed gas log appliance used in this product be installed in strict

accordance with NFPA 58, NFPA 54/ANSI Z223.1 and the gas log manufacturer’s explicit installation, sizing

and operation instructions. It is the responsibility of the general contractor to provide adequate clearances

from all firebox surfaces as specified in this manual.

INSTALLER: Leave this manual with the appliance

CONSUMER: Retain this manual for future reference

Be Sure to Read Entire Manual Before Beginning Construction.

Contents of this manual may change without prior notification.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

Содержание Magnum 86072-60

























































Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды

Isokern Magnum 86072-60, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Magnum 86072-60

Отзывы:

Бренды по названию

Популярные бренды