Intel P4000M Скачать руководство пользователя страница 48

Страница: 48 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

10. Install the chassis cover. For instructions, see “Installing the Chassis Cover”.

11. Plug all peripheral devices and the AC power cable into the server.

12. Power up the server.

Removing and Installing 8x3.5'' Hotswap Hard Drive
Cage Assembly

NOTE

This procedure applies only to the Intel

Server Chassis P4000M family with 8x3.5'' hotswap hard disk

drive cage configuration.

Removing 8x3.5'' Hotswap Hard Drive Cage Assembly

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the front bezel if it is installed. For instructions, see “Removing the Front Bezel (Pedestal

Only)”.

5. Disconnect the power and data cables to the backplane.

6. Use screwdriver to release the hotswap hard drive cage (see letter

) from the chassis and remove

the hotswap hard drive cage (see letter

Figure 55. Removing the 8x3.5

Hotswap HDD Cage Assembly

Содержание P4000M
















































































































Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды

Intel P4000M, Руководство по обслуживанию

Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды