Intel P4000M Скачать руководство пользователя страница 40

Страница: 40 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Removing and Installing Fixed Hard Drive(s)

NOTE

This procedure applies only to the Intel

Server Chassis P4000M family with fixed HDD configuration.

Removing Fixed Hard Drive(s)

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the front bezel if it is installed. For instructions, see “Removing the Front Bezel”.

5. Remove the Fixed HDD EMI shield. For instructions, see “Removing the Fixed HDD EMI Shield”.

6. Remove power and data cables from the hard drive connectors.

7. Pull out the HDD carrier tray.

Figure 40. Removing Fixed Hard Drives

8. Use screwdriver to release the 3.5” or 2.5” HDD from the carrier tray.

Figure 41. Removing the 3.5” HDD from Fixed HDD tray

Содержание P4000M
















































































































Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды

Intel P4000M, Руководство по обслуживанию

Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды