Intel P4000M Скачать руководство пользователя страница 68

Страница: 68 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Removing a DVD or CD-ROM Drive

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the front bezel if it is installed. For instructions, see “Removing the Front Bezel”.

5. Disconnect the power and data cables to the DVD/CD-ROM drive.

6. Press on the slide release latches (see letter

in the following figure) and pull the DVD/CD-ROM

drive/slide assembly from the chassis (see letter

in the following figure). Remove the slides from

the DVD or CD-ROM drive (see letter

Figure 84. Removing DVD or CD-ROM Drive

7. If not replacing with another drive, reinsert an EMI shield into chassis (see below illustration).

Figure 85. Re-inserting Empty EMI Shield

Содержание P4000M
















































































































Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды

Intel P4000M, Руководство по обслуживанию

Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды