Intel P4000M Скачать руководство пользователя страница 38

Страница: 38 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Installing the Hotswap Fan

1. Observe the safety and ESD precautions at the beginning of this book.

2. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

3. Insert hotswap fan into corresponding chassis slot until it clicks into place.

Figure 37. Installing Hotswap Fan

Removing and Installing the Fixed HDD EMI Shield

NOTE

For a rack configuration or chassis on its side, position the chassis hanging over the edge of a table or

workbench before removing the bezel.

This procedure applies only to the Intel

Server chassis P4000M family with fixed HDD configuration.

Removing the Fixed HDD EMI Shield

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the front bezel. For instructions, see “Removing the front bezel”.

5. Press the clip (see letter

) and lift the EMI shield (see letter

) and move EMI shield outward from

the chassis.

Содержание P4000M
















































































































Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды

Intel P4000M, Руководство по обслуживанию

Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды