Intel P4000M Скачать руководство пользователя страница 77

Страница: 77 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Replacing the Power Distribution Board for
460W/750W PSUs

WARNING

Hazardous voltage, current, and energy levels are present inside the power supply. There are no

user-serviceable parts inside it; servicing should be done by technically qualified personnel.

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the air duct. For instructions, see “Installing the Airduct”.

5. Disconnect all internal power cables from chassis components and server board.

6. If present, press on green latch in the direction shown while pulling on handle to remove power

supply from chassis. Repeat this step for the second hotswap power supply if it is installed.

Figure 103. Removing Hotswap Power Supply Module from Chassis

7. Loosen screws securing the bracket with power distribution board to the chassis (see letter

and

Figure 104. Loosening the Bracket with Power Distribution Board from Chassis

Содержание P4000M
















































































































Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды

Intel P4000M, Руководство по обслуживанию

Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды