Intel P4000M Скачать руководство пользователя страница 58

Страница: 58 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Figure 67. Two 8x2.5” Hot Swap Backplane Cable Connections

7. Install the air duct if the air duct is removed. For instructions, see “Installing the Airduct”.

8. Install the chassis cover. For instructions, see “Installing the Chassis Cover”.

9. Plug all peripheral devices and the AC power cable into the server.

10. Power up the server.

Removing and Installing 8x2.5'' Hotswap Backplane

Removing 8x2.5'' Hotswap Backplane

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the front bezel if it is installed. For instructions, see “Removing the Front Bezel (Pedestal

Only)”.

5. Remove the 8x2.5'' Hotswap Hard drives cage. For instructions, see “Removing 8x2.5'' Hotswap Hard

Drive Cage Assembly”.

6. Remove the screw on the backplane (see letter

7. Push the backplane (see letter

) and remove the backplane from the cage (see letter

Содержание P4000M
















































































































Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды

Intel P4000M, Руководство по обслуживанию

Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды