Intel P4000M Скачать руководство пользователя страница 88

Страница: 88 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

9. Slide the front panel out from the front of the chassis to the place (see Letter

) so that you can reach

the front panel cable and intrusion cable connectors at the rear of the front panel. Then disconnect

the front panel cable and intrusion switch cable from the front panel board (see Letter

Figure 120. Disconnecting the Cables from Front Panel Board

10. Slide the front panel tray out.

Installing the Front Panel Tray

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Remove the front bezel if it is installed. For instructions, see “Removing the Front Bezel”.

5. Remove the air duct if it is installed.

6. Attach the front panel cable and the chassis intrusion cable (see Letter

) to the front panel board.

Figure 121. Connecting the Cables to the Front Panel Board

Содержание P4000M
















































































































Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды

Intel P4000M, Руководство по обслуживанию

Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды