Intel P4000M Скачать руководство пользователя страница 29

Страница: 29 / 111

Hardware Installations and Upgrades

Intel

Server Chassis P4000M Service Guide

Removing and Installing the Front Bezel (Pedestal
Only)

Removing the Front Bezel (Pedestal Only)

NOTE

For a rack configuration or chassis on its side, position the chassis hanging over the edge of a table or

workbench before removing the bezel.

There are two type of bezel assembly. One type is for fixed HDD configuration, the other type is for

Hotswap HDD configuration.

CAUTION

Do not rotate the bezel assembly more than 40 degrees or you will damage the bezel assembly.

1. Observe the safety and ESD precautions at the beginning of this book.

2. Power down the server and unplug all peripheral devices and the AC power cable.

3. Remove the chassis cover. For instructions, see “Removing the Chassis Cover”.

4. Release the two plastic tabs on the left side of the bezel assembly to disengage the tabs, and rotate

the bezel assembly (see letter

) no more than 40 degrees outward.

5. At a 40-degree angle, push the bezel assembly away from the chassis (see letter

6. If the bezel assembly does not immediately disconnect from the chassis, tap the left-hand side of the

bezel assembly to disengage the bezel hooks on the right-hand side of the chassis.

Figure 20. Removing the Front Bezel

Содержание P4000M
















































































































Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды

Intel P4000M, Руководство по обслуживанию

Результаты поиска

Содержание P4000M

Отзывы:

Похожие инструкции для P4000M

Бренды по названию

Популярные бренды