manualshive.com logo in svg

illumina Infinium HD Super Assay, Справочное руководство, Страница: 17 / 79

Поделиться
Скачать
illumina Infinium HD Super Assay Скачать руководство пользователя страница 17

Procedure

1

Pulse centrifuge the MSA1 plate at 280 × g.

2

Carefully remove the cap mat.

3

Add 50 µl FMS to each well of the MSA1 plate.

4

Reseal with the cap mat using the original orientation.

5

Vortex at 1600 rpm for 1 minute, and then centrifuge the plate at 280 × g.

6

Incubate on the preheated heat block for 1 hour.
If you are continuing, you can leave the plates on the heat block until you have completed preparation for
the next step, no longer than 2 hours.

SAFE STOPPING POINT

If you are stopping, seal the plate, and store at -25°C to -15°C for up to 24 hours.

Precipitate DNA

This step uses 100 % 2-propanol and PM1 to precipitate the DNA.

Consumables

u

100% 2-propanol

u

PM1(2 tubes)

u

Cap mat

Preparation

1

Do one of the following:

u

If proceeding immediately from

Fragment DNA

, leave the MSA1 plate on the heat block until

preparation is complete.

u

If the MSA1 plate was stored at -25°C to -15°C, thaw at room temperature, pulse centrifuge
at 280 × g, and preheat the heat block to 37°C.

2

Prepare the following consumable.

Item

Storage

Instructions

PM1

2°C to 8°C

Thaw to room temperature and invert 10 times to mix.

3

Remove the cap mat.

Procedure

1

Add 100 μl PM1 to each well of the MSA1 plate.

2

Reseal with the cap mat using the original orientation.

3

Vortex the plate at 1600 rpm for 1 minute.

4

Incubate on the preheated heat block for 5 minutes.

5

Pulse centrifuge at 280 × g for 1 minute.

6

Set the centrifuge at 4°C in preparation for the next centrifuge step.

Document # 11322427 v03

For Research Use Only. Not for use in diagnostic procedures.

11

Infinium HD Super Assay Reference Guide

Содержание Infinium HD Super Assay
















































































Отзывы:

Нет отзывов