IEI Technology WAFER-LX Скачать руководство пользователя страница 33

Страница: 33 / 144

WAFER-LX User Manual

1x3 WAFER 2mm connector.

Using CN2 as a Power Feature Connector:

The SBVCC connector can support an advanced soft power switch function. If an

ATX power supply is used, connect an ATX-to-4P power cable between the SBVCC connector

and ATX power source. Also connect a power on/off switch to the ATX ON/OFF switch

previously mentioned. Note that your ATX power supply should provide a 10mA load on the

5V source standby lead for this function to take effect.

IEI provides an ATX-to-4P adapter cable that comes with a 20-pin ATX connector, a 3-pin

connector to the SBVCC (CN2) connector, and a 4P power connector.

This board uses an

adapter cable different from that provided with the previous WAFER models

, please

refer to

Appendix B

for more information.

Using CN2 as a Configuration Jumper:

A jumper cap is installed on pins 1 and 2 as factory default (pin1=+5VSB; pin2=+5V). If the

WAFER-LX is connected to an AT power, let the jumper stay on pins 1 and 2. If connected to

an ATX power source, remove the jumper cap.

Table 2-4 CN2 SBVCC: ATX Power Feature Pinouts

PIN

DESCRIPTION

1 5VSB

2 +5V

3 GND

Figure 2-6 CN2 SBVCC ATX Power Feature

3. CN3: IVTC LCD Panel Inverter Backlight Control Connector

This connector comes as a 1x5 pin Wafer 2mm connector.

Table 2-5 CN3 IVTC Inverter Control Pinouts

PIN

DESCRIPTION

PIN

DESCRIPTION

1 VCC12 2

GROUND

3 VEEON 4 BLADJ

2-12

IEI

Technology, Corp.

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды