IEI Technology WAFER-LX Скачать руководство пользователя страница 62

Страница: 62 / 144

WAFER-LX

Optional Floppy Drive Connector (CN31)

This connector provides access to one (1) externally mounted floppy drive (3.5”-profile, 720 KB,

1.44 MB, and 2.88 MB types floppy drive).

A 26-pin FPC connector cable is required for the connection to floppy drives. The cable should

come with a 26-pin FPC-cable connector and floppy disk drive connector on the other end.

Connecting the Floppy Drive

1. Plug the 26-pin FPC-cable connector into CN31. Make sure that the red wire corresponds to

pin one on the connector.

2. Attach the appropriate connector on the other end of the cable to the floppy drive. You can use

only one connector in the set.

Compact Flash Disk

When appropriately formatted, a compact Flash disk can serve as a bootable hard drive in

applications where installation space is limited. The Compact Flash card occupies a secondary

IDE channel. Configuration options can be found through the BIOS configuration utility.

Parallel Port Connector (CN15)

Parallel port connects to a printer. The WAFER-LX comes with a multi-mode (ECP/EPP/SPP)

parallel port. The CN15 parallel port interface features a 26-pin flat-cable connector that requires

an adapter cable if a traditional DB-25 connector is preferred. The parallel interface can be

re-assigned to LPT2 or LPT3 through the BIOS configuration utility.

The default interrupt channel is IRQ7. Select ECP or EPP DMA mode using the BIOS

configuration utility.

3-9

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды