IEI Technology WAFER-LX Скачать руководство пользователя страница 40

Страница: 40 / 144

WAFER-LX

13. CN13: AT Power ON/OFF Button Connector

This connector is used to connect a chassis power On/Off button using an adapter cable.

This connector is closely related to JP1 configuration. The use of this connector is briefed as

follows:

1. Using

ATX

power: CN13 connects to a power switch, and the JP1 jumper should be

left open.

2. Using

power:

The pins on JP1 are shorted by a jumper cap. The reason why

JP1 should be shorted is because the AMD Southbridge is

designed without the consideration for a power button signal and

the shorted JP1 provides a hardware feedback to initiate the

system.

Table 2-13

CN13 Power ON/OFF Button Connector Pinouts

PIN

DESCRIPTION

PWR_BTN#

2 GND

Figure 2-13 CN13 Power ON/OFF Button Connector

14. CN14: Digital I/O Connector

This Digital I/O port is managed through AMD CS5536AD Southbridge. The first table below

shows the CN14 port pinouts. The second table shows the Digital I/O port assembly codes.

Table 2-14

CN14 Digital I/O Connector Pinouts

PIN

DESCRIPTION

PIN

DESCRIPTION

GND 2

+5V

3 DIO_IN0

4 DIO_OUT0

DIO_IIN1 6

DIO_OUT1

2-19

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды