IEI Technology WAFER-LX Скачать руководство пользователя страница 98

Страница: 98 / 144

WAFER-LX

Standby Mode

Defines the continuous idle time before the system enters Standby Mode. If any item defined is

enabled & active Standby timer will be reloaded. The standby mode turns screen and hard drives

off

Suspend Mode

Defines the timeout before the system enters the Suspend Mode. The suspend mode powers
down the system and keeps a trickle of power. If an interrupt to RTC reaches, the system wakes
up.

Video Off In Suspend [Yes]

The

Video Off In Suspend

option allows you to specify whether the display monitor is turned off

or remains on when the systems enters a suspend state.

The display monitor will remain on when the system is in

suspend mode.

Yes

EFAULT

)

The display monitor will be turned off when the system is in

suspend mode.

Suspend Type [Stop Grant]

The

Suspend Type

option allows you to determine what suspend state the CPU will go into when

the system is in the suspend state.

Stop Grant

EFAULT

)

When the CPU is in the stop grant state the bus

clock (BCLK) continues to run. Snoops and

interrupts are also allowed in the stop grant state.

Thus, the CPU can operate in a lower power state

yet can respond to snoops and interrupts.

PwrON Suspend

4-33

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды