IEI Technology WAFER-LX Скачать руководство пользователя страница 78

Страница: 78 / 144

WAFER-LX

Third Boot Device

EFAULT

: LS120]

The

Boot Device

configuration options allow you to select the order of devices the computer will

boot from. Using the default values, the system will first look for a FDD to boot from. If it cannot find

an FDD it will use an HDD to boot from. If both a FDD and a HDD are unavailable then the system

will boot from a LS120 (Super Disk) drive.

Boot Device

configuration options are:

1. Floppy

2. LS120

3. HDD-0

4. SCSI

5. CDROM

6. HDD-1

7. ZIP100

8. USB-FDD

9. USB-ZIP

10. USB-CDROM

11. USB-HDD

12. LAN

13. Disabled

Boot Other Device [Enabled]

The

Boot Other Device

option determines whether the CPU card will use a second or third boot

device if the first boot device is not found.

Enabled

EFAULT

)

The system will look for second and third boot devices if

the first one is not found.

Disabled

The system will not look for second and third boot device

if the first one is not found.

Swap Floppy Drive [Disabled]

This option should not avail because FPC interface only allows the connection to one floppy drive.

Boot Up Floppy Seek [Enabled]

4-13

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды