IEI Technology WAFER-LX Скачать руководство пользователя страница 19

Страница: 19 / 144

WAFER-LX

1.3

Technical Specifications

Table 1-2 Technical Specifications

CPU

Embedded AMD Geode [email protected] processor at 500MHz
frequency

Chipset

Geode CS5536D as Southbridge

Memory

One 64-bit PC 100/133 144-pin SODIMM socket that supports
SDRAM memory up to 512MB

Display Controller

Integrated ProSavage4 w/ 3D/2D/Video controller

Supports AGP 4x performance

Supports single cycle 128-bit 3D architecture

24-bit TTL/single-channel 18-bit DSTN/TFT flat panel interface

Integrated 2-channel 110MHz LVDS interface

Support for all resolutions up to 1024X768 pixels

Hardware Suspend/Standby control

PCI Interface

PCI 2.2 compliant, 32-bit 3.3V PCI interface w/ 5V tolerant
inputs

Up to 5 PCI masters

PCI to system memory data streaming support

10/100Mbps

Realtek8100C

Ethernet

Controller

IEEE 802.3 10/100M Base-T standard auto-sensing interface to
10Mbps or 100Mbps networks through an onboard RJ-45
connector.

BIOS

AMI 256KB Flash memory

Compact Flash

Disk

Runs in true IDE mode that simulates the operation of a physical
IDE hard drive. It can be used with a passive adapter in a Type
II socket in DMA mode.

IDE Interface

Supports one ATA33/66/100 IDE channel with the connectivity
to two hard disk drives

FDD Interface

Supports one optional floppy disk drive, 3.5” (720KB or 1.44MB )
by a 26-pin FPC connector cable.

1-9

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды