IEI Technology WAFER-LX Скачать руководство пользователя страница 100

Страница: 100 / 144

WAFER-LX

that if you selected max. or min. as the setting for the

Power Management

option, you will not be

able to configure this setting. The following settings can be made.

Disable (D

EFAULT

)

1 Min

2 Min

3 Min

4 Min

5 Min

6 Min

7 Min

8 Min

9 Min

10 Min

11 Min

12 Min

13 Min

14 Min

15 Min

Soft –Off by PWR-BTTN [Instant-Off]

The

Soft –Off by PWR-BTTN

option allows you to define how the system responds when the

power button is pushed. You may choose to allow the system to be either turned off completely or

enter into a suspend mode.

Instant-Off

EFAULT

)

The system will be turned off as soon as the power

button is pressed.

Delay 4 Sec

The power button must be pressed for more than

four seconds before it is turned off. If it is pressed for

less than four seconds the system will enter a

suspend state.

Wake-Up by PCI Card [Enabled]

The

Wake-Up by PCI Card

option allows users to wake a system in a suspended state through a

network. A wakeup signal from a network can be routed directly through the PCI card.

Disabled

The system cannot be woken from a suspend state

4-35

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды