IEI Technology WAFER-LX Скачать руководство пользователя страница 71

Страница: 71 / 144

WAFER-LX User Manual

Date [mm:dd:yy]

Allows you to set the system date.

Time [Day hh/mm/ss]:

Allows you to set the system time.

IDE Master and IDE Slave

When entering setup, BIOS auto detects the presence of IDE devices. This displays the status of

the auto detected IDE devices. The following IDE devices will be detected and are shown in the

Standard CMOS Features

menu:

1. Primary

IDE

Master

2. Primary

IDE

Slave

Secondary IDE Master

Secondary IDE Slave

The IDE Configuration menu (

BIOS Menu 3

) allows you to set or change the configurations for the

IDE devices installed in the system. If an IDE device is detected, and one of the above listed four

BIOS configuration options are selected, the IDE configuration options shown in

Section 1.1.6

appear.

Drive A [1.44M, 3.5in]

The

Drive A

configuration option determines the type of floppy drive installed in the system. The

floppy drive configuration options are listed below.

None

1.44M, 3.5 in (D

EFAULT

)

Halt On

The

Halt On

category allows users to determine whether the computer will stop if an error is

detected during power up.

All Errors

EFAULT

)

Whenever BIOS detects a non-fatal error the

system will be stopped and you will be

prompted.

No Errors

The system boot will not be stopped for any

errors that may be detected

All, But Keyboard

The system boot will not stop for a keyboard

error; it will stop for all other errors.

All, But Diskette

The system boot will not stop for a disk error;

it will stop for all other errors.

4-6

IEI

Technology, Corp.

4-6

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды