IEI Technology WAFER-LX Скачать руководство пользователя страница 101

Страница: 101 / 144

WAFER-LX User Manual

through the network via a PCI card

Enabled

EFAULT

)

The system can be woken from a suspend state

through the network via a PCI card

Power On by Ring [Enabled]

The

Power On by Ring

option allows users to determine whether or not the system can be roused

from a suspend state when the modem rings.

Disabled

The system will not be woken from a suspend state

when the modem rings

Enabled

EFAULT

)

The system will be woken from a suspend state

when the modem rings

USB KB Wake-Up From S3 [Disabled]

If you selected either the S3(STR) or the S1&S3 option in the

ACPI Suspend Type

option, you will

be able to configure the

USB KB Wake-Up From S3

. This option allows you to wake the system

from an S3 suspend state using the keyboard.

Disabled

EFAULT

)

Keyboard cannot be used to rouse the system from

the S3 suspend state

Enabled

Keyboard can be used to rouse the system from the

S3 suspend state

Resume by Alarm [Disabled]

The

Resume by Alarm

option allows you tell the computer when it should be roused

from a suspend state.

Disabled

EFAULT

)

No time is specified for when the computer should

be roused from a suspend state

Enabled

The date and time the computer must be roused

from a suspend state is specified

x Date(of Month) Alarm [0]

The

Date(of Month) Alarm

option can only be configured if the

Resume by Alarm

option has

been enabled. When you select this option you will be asked to enter a number between 0 and 31

to specify the date of the current month that you would like the system to be roused.

4-36

IEI

Technology, Corp.

4-36

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды