IEI Technology WAFER-LX Скачать руководство пользователя страница 87

Страница: 87 / 144

WAFER-LX User Manual

Precharge dealy (tRAS) [12]

The

Precharge Dealy

option

allows you to set the time it takes for the RAS to start retrieving the

actual data after a request has been issued to the memory module.

(To be able to change this

configuration option the

DRAM RAS# Precharge

configuration option must be set to “

Manual

”)

The following configuration options are available,

1. Auto

2. 2

nanoseconds

3. 3

nanoseconds

4. 4

nanoseconds

5. 5

nanoseconds

6. 6

nanoseconds

7. 7

nanoseconds

8. 8

nanoseconds

9. 9

nanoseconds

10. 10

nanoseconds

11. 11

nanoseconds

12.

12 nanoseconds (D

EFAULT

)

13. 13

nanoseconds

14. 14

nanoseconds

15. 15

nanoseconds

System Memory Frequency

The

System Memory Frequency

configuration option allows you to manually select the speed of

the installed memory module. The default value is 533MHz. If you are not certain of what value to

select, select “

Auto

” and the BIOS will automatically detect the speed. (To be able to change this

configuration option the

DRAM RAS# Precharge

configuration option must be set to “

Manual

”)

The following configuration options are available,

1. Auto

2. 333MHz

3. 400MHz

4. 533MHz

EFAULT

)

SLP_S4# Assertion Width [4 to 5 sec]

The following configuration options are available,

4-22

IEI

Technology, Corp.

4-22

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды