IEI Technology WAFER-LX Скачать руководство пользователя страница 59

Страница: 59 / 144

WAFER-LX User Manual

JP1 (AT/ATX Mode Selector)

This jumper block controls the way you connect to a power supply

The CN13 connector is used to connect a chassis power On/Off button using an adapter cable.

The CN13 connector is configured through the JP1 jumper. The use of this connector is

briefed as follows:

1. Using

ATX

power: CN13 connects to an externally implemented power switch, and

the JP1 jumper should be left open.

2. Using

power:

The pins on JP1 are shorted by a jumper cap. The reason why

JP1 should be shorted is because the AMD Southbridge is

designed without the consideration for a power button signal and

the shorted JP1 provides a hardware feedback to initiate the

system. The power on/off function is then managed by the AT

power switch button.

JP1 Pin Configuration

Table 3

1 JP1 Pin Configuration

JP1

Power Mode Selector

1 AUTO_SW#

2 PWRBTN#

JP2: COM3 Serial Port Operation Mode Selector

This jumper block allows you to select an operation mode for the COM2 serial port (Default:

1-2).

Table 3-2 JP2

Pinouts

PIN

COMBINATION

DESCRIPTION

1-2 RS-422

(default)

2-3 RS-485

3-6

IEI

Technology, Corp.

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды