IEI Technology WAFER-LX Скачать руководство пользователя страница 81

Страница: 81 / 144

WAFER-LX User Manual

OS Select For DRAM > 64MB [Non-OS2]

The

OS Select For DRAM > 64MB

option allows you to specify the operating system you are

using.

Enabled

Only select this if you are using the OS/2 operating

system

Disabled

EFAULT

)

If you are not using the OS/2 operating system then

disable this function.

Video BIOS For DRAM [Disabled]

When enabled, the video BIOS is copied to the system RAM for quicker access. Shadowing

boosts BIOS turnaround speed for that BIOS is accessed by CPU through the memory bus rather

than the original 8-bit X bus.

Small Logo (EPA) Show [Disabled]

The

Small Logo (EPA) Show

option determines if the

Environmental Protection Agency (EPA)

logo will appear during the system boot-up process. If it is enabled then the boot up process may

be delayed.

Enabled

EPA logo will appear during the boot up process.

Disabled

EFAULT

)

EPA logo will not appear during the boot up process.

Delay For HDD (Secs) [3]

A large number can be applied for slowly-initiated (longer spin-up time) hard drives depending on

the specifications provided by your hard drive vendors.

Cyrix 6x86/MII CPPUID [Enabled]

This option determines whether to use the function of controlling or accessing the Cyrix 6x86/MII

CPU ID.

4-16

IEI

Technology, Corp.

4-16

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды