IEI Technology WAFER-LX Скачать руководство пользователя страница 93

Страница: 93 / 144

WAFER-LX User Manual

BIOS Menu 10: Integrated Peripherals

Master/Slave Drive PIO Mode [Auto]

PIO means Programmed Input/Output. Instead of constantly issuing BIOS commands to

facilitate I/O transfers to and from the hard disk drives, the PIO mode allows the BIOS to issue I/O

requests and let CPU and IDE controller to fulfill the requests. Four modes from 0 to 4 are

supported.

IDE Primary Master PIO

IDE Primary Slave PIO

IDE Secondary Master PIO

IDE Secondary Slave PIO

Auto

EFAULT

) Allows the computer to select the correct mode

PIO mode 0 selected with a maximum transfer rate of 3.3MBps

PIO mode 1 selected with a maximum transfer rate of 5.2MBps

PIO mode 2 selected with a maximum transfer rate of 8.3MBps

PIO mode 3 selected with a maximum transfer rate of 11.1MBps

PIO mode 4 selected with a maximum transfer rate of 16.6MBps

IDE Primary Master/Slave UDMA [Auto]

The Ultra DMA (UDMA) mode for the following HDDs can all be selected.

1. IDE Primary Master UDMA

2. IDE Primary Slave UDMA

3. IDE Secondary Master UDMA

4. IDE Secondary Slave UDMA

Auto

EFAULT

)

Allows the computer to select the correct UDMA

Disabled

Disables the UDMA for the HDD device

IDE DMA transfer access [Enabled]

The

IDE DMA transfer access

option allows you to determine whether or not the IDE device

installed in the system will have a DMA device.

Disabled

The IDE HDD installed in the system will not have DMA

transfer access

4-28

IEI

Technology, Corp.

4-28

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды