IEI Technology WAFER-LX Скачать руководство пользователя страница 111

Страница: 111 / 144

WAFER-LX User Manual

The above options all have the same default and the same options. These are listed below.

PCI Device

EFAULT

)

The IRQ is assigned to legacy ISA for devices compliant

with the original PC AT bus specification, PCI/ISA PNP for

devices compliant with the Plug and Play standard

whether designed for PCI or ISA bus architecture.

Reserved

The IRQ is reserved by BIOS

PCI/VGA Palette Snoop [Disabled]

The

PCI/VGA Palette Snoop

option allows you determine whether or not some special VGA cards,

high-end hardware MPEG decoders and other similar devices are allowed to look at the VGA

palette on the video card so these devices can determine what colors are in use. This option is

only

very

rarely needed. It should be left at "Disabled" unless a video device specifically requires

the setting enabled upon installation.

Disabled

EFAULT

)

Does not allow the graphics devices to examine the VGA

palette on the graphics card

Enabled

Does allow the graphics devices to examine the VGA palette

on the graphics card

INT Pin # Assignment [Auto]

The

INT Pin # Assignment

allows you to customize the IRQs for the specified devices assigned

to the

INT Pin #

. IRQs for the following

INT Pin #

can be assigned.

INT Pin 1 Assignment

INT Pin 2 Assignment

INT Pin 3 Assignment

INT Pin 4 Assignment

INT Pin 5 Assignment

INT Pin 6 Assignment

INT Pin 7 Assignment

INT Pin 8 Assignment

Each

INT Pin # Assignment

has the following configuration options:

1. Auto

EFAULT

)

2. 3

3. 4

4. 5

4-46

IEI

Technology, Corp.

4-46

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды