IEI Technology WAFER-LX Скачать руководство пользователя страница 95

Страница: 95 / 144

WAFER-LX User Manual

the parallel port device and the transmission rates

between the two are much faster than the SPP mode.

ECP+EPP

The parallel port will be compatible with both ECP and

EPP devices

Normal

Parallel Port Mode [SPP]

These options are used to select the parallel port operating mode. The options are SPP, EPP,

ECP, ECP+EPP, and Normal. Two specific options avail when either of the ECP or EPP modes

is selected:

EPP Mode Select

and

ECP Mode Use DMA

If the

EPP mode

is selected in the

Parallel Port Mode

configuration option, you will be able to

configure the

EPP Mode Select

option. The EPP parallel port mode has two standards, EPP 1.7

and EP 1.9. This selection allows you to choose the standard the parallel port will operate in.

Please refer to the parallel device that your system will be connected to and select the EPP mode

accordingly.

EPP1.9

EPP 1.9 is selected as the EPP standard

EPP1.7

EFAULT

)

EPP 1.7 is selected as the EPP standard

x ECP Mode Use DMA [3]

If the

ECP mode

is selected in the

Parallel Port Mode

configuration option, you will be able to

configure the

ECP Mode Use DMA

option. This option determines the DMA channel the parallel

port uses when it is in the ECP mode.

Parallel port uses DMA Channel 1 in the ECP mode

3 (D

EFAULT

)

Parallel port uses DMA Channel 3 in the ECP mode

4-30

IEI

Technology, Corp.

4-30

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Бренды по названию

Популярные бренды