IEI Technology WAFER-LX Скачать руководство пользователя страница 79

Страница: 79 / 144

WAFER-LX User Manual

During the POST, BIOS will determine if the floppy disk drive installed has 40 or 80 tracks. 360K

FDDs have 40 tracks while 760K, 1.2M and 1.44M FDDs all have 80 tracks

Enabled

BIOS searches for a FDD to determine if it has 40 or 80

tracks. Note that BIOS cannot tell the difference between

720K, 1.2M or 1.44M drives as they all have 80 tracks.

Disabled

EFAULT

)

BIOS will not search for the type of FDD drive by track

number. Note that there will not be any warning message

if the drive installed is 360K.

Boot Up Numlock Status [On]

The

Boot Up Numlock Status

option allows you to determine the default state of the numeric

keypad.

Off

The keys on the keypad will be arrow keys

EFAULT

)

The keys on the keypad will be number keys

Typematic Rate Setting [Disabled]

Disabling the

Typematic Rate Setting

configuration option only allows one character to appear

onto the screen if a key is continuously held down. In other words, the BIOS will only report the key

is down. When this option is enabled, the BIOS will report as before, but it will then wait a moment,

and, if the key is still down, it will begin to report that the key has been depressed repeatedly. Such

a feature would be used to accelerate cursor movements with the arrow keys.

Disabled

EFAULT

)

Disables the typematic rate

Enabled

Enables the typematic rate

x Typematic Rate (Chars/sec) [6]

The

Typematic Rate

can only be configured if the

Typematic Rate Setting

is Enabled. The

Typematic Rate

configuration field determines the rate keys are accelerated.

EFAULT

)

6 characters per second

8 characters per second

10 characters per second

12 characters per second

15 characters per second

20 characters per second

4-14

IEI

Technology, Corp.

4-14

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды