IEI Technology WAFER-LX Скачать руководство пользователя страница 116

Страница: 116 / 144

WAFER-LX User Manual

NOTE:

The following discussion applies to DOS environment. It is recommended

you contact IEI support or visit our website for specific drivers for more

sophisticated operating systems, e.g., Windows and Linux.

The Watchdog Timer is a device to ensure that standalone systems can always recover from

catastrophic conditions that cause the CPU to crash. This condition may have occurred by EMI

or a software bug. When the CPU stops working normally, hardware on the board will perform

hardware reset (cold boot) to bring the system back to a known state.

Three I/O ports control the Watchdog Timer:

443

Write

Set Watchdog time period

443 (hex)

Read

Enable the refresh to the Watchdog Timer

043/843 (hex)

Read

Disable the Watchdog Timer

Table

1 I/O Ports to Watchdog Timer

Prior to enable the Watchdog Timer, users have to define the Timer first. The output data is a

value of time interval and the range of the value is from 01 (hex) to FF (hex) and the range for time

interval ranges from 1 second to 255 seconds.

DATA

TIME INTERVAL

01 1

sec

02 2

sec

03 3

sec

04 4

sec

- - -

FF 255

sec

Table

2 Watchdog Timer Output Data

This will enable and activate the countdown timer which eventually time out and reset the CPU to

ensure that this reset condition does not occur; the Watchdog Timer must be periodically

refreshed by reading the same I/O port 043/843H and 443H. This must be done within the time

A-2

IEI

Technology, Corp.

A-2

Содержание WAFER-LX

















































































































































Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды

IEI Technology WAFER-LX, Руководство пользователя

Результаты поиска

Содержание WAFER-LX

Отзывы:

Похожие инструкции для WAFER-LX

Бренды по названию

Популярные бренды