IEI Technology IMB-H110 Скачать руководство пользователя страница 77

Страница: 77 / 161

IMB-H110 microATX Motherboard

Page 62

Step 9:

Connect the 12 V power to the board.

Connect the 12 V power from the power

supply to the board.

Step 0:

4.4 Socket LGA1151 Cooling Kit Installation

WARNING:

DO NOT attempt to install a push-pin cooling fan.

The pre-installed support bracket prevents the board from

bending and is ONLY compatible with captive screw type cooling

fans.

The cooling kit can be bought from IEI. The cooling kit has a heat sink and fan.

WARNING:

Do not wipe off (accidentally or otherwise) the pre-sprayed layer of

thermal paste on the bottom of the heat sink. The thermal paste

between the CPU and the heat sink is important for optimum heat

dissipation.

To install the cooling kit, follow the instructions below.

Step 1:

A cooling kit bracket is pre-installed on the rear of the motherboard. See

Figure 4-5.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды