IEI Technology IMB-H110 Скачать руководство пользователя страница 86

Страница: 86 / 161

IMB-H110 microATX Motherboard

Page 71

4.8.4 Flash Descriptor Security Override Jumper

The flash descriptor security override jumper (J_FLASH2) allows to enable or disable the

ME firmware update. Refer to

Table 4-3

and

Figure 4-17

for the jumper location and

settings.

Setting Description

Short 1-2

Disabled (default)

Short 2-3

Enabled

Table 4-3: Flash Descriptor Security Override Jumper Settings

Figure 4-17: Flash Descriptor Security Override Jumper Location

To update the ME firmware, please follow the steps below.

Step 1:

Before turning on the system power, short pin 2-3 of the flash descriptor security

override jumper.

Step 2:

Update the BIOS and ME firmware, and then turn off the system power.

Step 3:

Remove the metal clip on the flash descriptor security override jumper or return

to its default setting (short pin 1-2).

Step 4:

Restart the system. The system will reboot 2 ~ 3 times to complete the ME

firmware update.

Step 0:

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды