IEI Technology IMB-H110 Скачать руководство пользователя страница 132

Страница: 132 / 161

IMB-H110 microATX Motherboard

Page 117

5.4.2 PCH-IO Configuration

Use the

PCH-IO Configuration

menu (

BIOS Menu 25

) to configure the PCH parameters.

Chipset

Auto Power Button Status

[Disable (ATX)]

Restore AC Power Loss

[Last State]

> PCI Express Configuration
> HD Audio Configuration

Power Saving Function(ERP)

[Disabled]

USB Power SW1

[+5V DUAL]

USB Power SW2

[+5V DUAL]

Select AC power state
when power is re-applied
after a power failure.

---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 25: PCH-IO Configuration

Restore AC Power Loss [Last State]

Use the

Restore AC Power Loss

BIOS option to specify what state the system returns to

if there is a sudden loss of power to the system.

Power Off

The system remains turned off.

Power On

The system turns on.

Last State

EFAULT

The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.

Power Saving Function(ERP) [Disabled]

Use the

Power Saving Function(ERP)

BIOS option to enable or disable the power

saving function.

Disabled D

EFAULT

Power saving function is disabled.

Enabled

Power saving function is enabled. It will reduce power

consumption when the system is off.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды