IEI Technology IMB-H110 Скачать руководство пользователя страница 116

Страница: 116 / 161

IMB-H110 microATX Motherboard

Page 101

Wake system with Fixed Time [Disabled]

Use the

Wake system with Fixed Time

option to enable or disable the system wake on

alarm event.

Disabled D

EFAULT

The real time clock (RTC) cannot generate a wake

event.

Enabled

If selected, the

Wake up every day

option appears

allowing you to enable to disable the system to wake

every day at the specified time. Besides, the

following options appear with values that can be

selected:

Wake

date

Wake

hour

Wake up minute

Wake

second

After setting the alarm, the computer turns itself on

from a suspend state when the alarm goes off.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды