IEI Technology IMB-H110 Скачать руководство пользователя страница 124

Страница: 124 / 161

IMB-H110 microATX Motherboard

Page 109

5.3.11 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 18

) to read USB configuration

information and configure the USB settings.

Advanced

USB Configuration

USB Controllers:
1 XHCI
USB Devices:
1 Keyboard, 1 Hub

Legacy USB Support

[Enabled]

Enables Legacy USB
support. AUTO option
disables legacy support
if no USB devices are
connected. DISABLE
option will keep USB
devices available only
for EFI applications.
---------------------

ÆÅ

: Select Screen

↑

↓

: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4: Save & Exit
ESC: Exit

BIOS Menu 18: USB Configuration

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support. Normally if this option is not enabled, any attached USB mouse or USB keyboard

does not become available until a USB compatible operating system is fully booted with all

USB drivers loaded. When this option is enabled, any attached USB mouse or USB

keyboard can control the system even when there is no USB driver loaded onto the system.

Enabled D

EFAULT

Legacy USB support enabled

Disabled

Legacy USB support disabled

Auto

Legacy USB support disabled if no USB devices are

connected

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды