IEI Technology IMB-H110 Скачать руководство пользователя страница 23

Страница: 23 / 161

IMB-H110 microATX Motherboard

Page 8

I/O Interface Connectors

Audio Connectors

Line-in, line-out and mic-in audio jacks on rear panel

One internal front panel audio connector (10-pin header)

Chassis Intrusion

One 2-pin header

Digital I/O

8-bit digital I/O

Ethernet

Two RJ-45 GbE ports

Fan

One 4-pin CPU smart fan connector

One 3-pin system smart fan connector

Front Panel

One 14-pin header (power LED, HDD LED, speaker, power

button, reset button)

One 4-pin wafer connector

Internal DisplayPort

One 20-pin box header

Keyboard and

Mouse

One internal keyboard and mouse connector (6-pin wafer)

LAN LED

Two

2-pin headers for LAN1 LED and LAN2 LED

Parallel Port

One parallel port via internal 26-pin box header

Serial ATA

Four SATA 6Gb/s connectors

Serial Ports

Ten RS-232 via internal 10-pin headers

Two RS-232/422/485 via internal 10-pin headers

SMBus

One 4-pin wafer connector

TPM

One via 20-pin header

USB 2.0

Six USB 2.0 ports on rear panel

Two USB 2.0 ports via internal pin headers

USB 3.0

Four USB 3.0 ports on rear panel

* The Windows® 7 installation media does not include native

driver support for USB 3.0. In order to use the USB keyboard or

mouse connected to a USB 3.0 port during OS installation, the

user has to update the Windows® 7 installation image so that it

contains USB 3.0 drivers. Please refer to Section 4.10 for

detailed installation procedures.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды