IEI Technology IMB-H110 Скачать руководство пользователя страница 118

Страница: 118 / 161

IMB-H110 microATX Motherboard

Page 103

Console Redirection [Disabled]

Use

Console Redirection

option to enable or disable the console redirection function.

Disabled D

EFAULT

Disabled the console redirection function

Enabled

Enabled the console redirection function

The following options are available in the

Console Redirection Settings

submenu when

the

Console Redirection

option is enabled.

Terminal Type [ANSI]

Use the

Terminal Type

option to specify the remote terminal type.

VT100

The target terminal type is VT100

VT100+

The target terminal type is VT100+

VT-UTF8

The target terminal type is VT-UTF8

ANSI D

EFAULT

The target terminal type is ANSI

Bits per second [115200]

Use the

Bits per second

option to specify the serial port transmission speed. The speed

must match the other side. Long or noisy lines may require lower speeds.

9600

Sets the serial port transmission speed at 9600.

19200

Sets the serial port transmission speed at 19200.

57600

Sets the serial port transmission speed at 57600.

115200 D

EFAULT

Sets the serial port transmission speed at 115200.

Data Bits [8]

Use the

Data Bits

option to specify the number of data bits.

Sets the data bits at 7.

8 D

EFAULT

Sets the data bits at 8.

Содержание IMB-H110


































































































































































Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды

IEI Technology IMB-H110, Руководство пользователя

Результаты поиска

Содержание IMB-H110

Отзывы:

Похожие инструкции для IMB-H110

Бренды по названию

Популярные бренды